Noticed in Dirt Rally 2 the wheel jolts to the right, quite forcefully, after it loads into the Drivers seat before the race starts, either a in rally race or a rallycross race.
Looks like a Virus scanner called "microsoft" is saying 1.47b is infected? it was the only one out of 57, but typically when there is a one-off, it's some random scanner that's not widely known.
Hi Edgar, i had freezes with my Formula V2 and my DD1. After some time (beginning weeks between freezes, at the end i cant drove one lap at leman without) the freezes destroy my races. I cant shift or make any input direkt on the wheel. Had to restart the Base and than everythink works fine till next freeze. Try all driver Versions and also clean new installation of Windows.
After three month of testing i decide to start a RMA and send it back.
I decide now to go with a Porsche 911 GT Wheel. Support of Fanatec tell me if i order the Formula wheel again it is not sure that it work 100% without issue.
This version seems to give me problems with braking.
I am new with fanatec so I may have got it wrong.
When I use the beta & set my brakes with the windows app so I don't need to press hard to get full braking then when i connect my PS4 & use ACC the 1st time I use my brakes I can press with less force to stop the car.
as I keep using the brakes I notice I have to press more & more until I fully press down on the sponge to get full braking.
So it seems the settings change as I drive more.
Drv 311 fwv476
Menu now shows :ABS
Now I have gone to (shown on wheel base) QA ver 476 / 18 which seems to give me consistent braking.
What difference is there between versions 670 and 674 of the Wheel Base Firmware? Is it ok to run firmware version 670 with the new driver package? Version 674 is causing random disconnections. I have reinstalled the old firmware version for the Wheel Base, but am running the new firmware version for the motor and wheel. It seems to work ok.
Comments
Noticed in Dirt Rally 2 the wheel jolts to the right, quite forcefully, after it loads into the Drivers seat before the race starts, either a in rally race or a rallycross race.
@Marcel Pfister
Looks like a Virus scanner called "microsoft" is saying 1.47b is infected? it was the only one out of 57, but typically when there is a one-off, it's some random scanner that's not widely known.
https://www.virustotal.com/gui/file/57e78cf0139009973435ee23e7607d07f97c7564d93925967b7870285cb1355a/detection
Can someone please post again the link so that I can download the Fanatec Beta Driver V373 for my CSL??? Appreciate it
First post in this thread.
Go to first page...
Hi Edgar, i had freezes with my Formula V2 and my DD1. After some time (beginning weeks between freezes, at the end i cant drove one lap at leman without) the freezes destroy my races. I cant shift or make any input direkt on the wheel. Had to restart the Base and than everythink works fine till next freeze. Try all driver Versions and also clean new installation of Windows.
After three month of testing i decide to start a RMA and send it back.
I decide now to go with a Porsche 911 GT Wheel. Support of Fanatec tell me if i order the Formula wheel again it is not sure that it work 100% without issue.
Bernd
Few posts up, I have same issue. Maurice explained:
"Known issue, no ETA for a fix yet but its known for a VERY long time already."
This version seems to give me problems with braking.
I am new with fanatec so I may have got it wrong.
When I use the beta & set my brakes with the windows app so I don't need to press hard to get full braking then when i connect my PS4 & use ACC the 1st time I use my brakes I can press with less force to stop the car.
as I keep using the brakes I notice I have to press more & more until I fully press down on the sponge to get full braking.
So it seems the settings change as I drive more.
Drv 311 fwv476
Menu now shows :ABS
Now I have gone to (shown on wheel base) QA ver 476 / 18 which seems to give me consistent braking.
What difference is there between versions 670 and 674 of the Wheel Base Firmware? Is it ok to run firmware version 670 with the new driver package? Version 674 is causing random disconnections. I have reinstalled the old firmware version for the Wheel Base, but am running the new firmware version for the motor and wheel. It seems to work ok.
The RMA process is a joke, they have my $$ and my gear, I have nothing and they will not respond to me.
Does anyone know why it won't let me update the firmware on the Podium Hub?
On new CSL Elite Steering Wheel WRC page https://fanatec.com/eu-en/csl-elite-steering-wheel-wrc There is driver 374 listed.
Do we have changelog :)
edit .. aah in the zip file it is changelog.txt
The new driver 374 is not marked as beta driver, is this an official release driver?