Brand new CSL Elite + Formula V2 + CSL Pedals working fine till i updated to those drivers to try Fanalab.
Wheel was like driven by the devil, as i hit curbs it was going to break my desk and 4 tim drivers crashed and my wheel has been disconnected, now i rolled back to v334 downgrading everything except Formula FW and seems, SEEMS it works fine again, but i can't use Fanalabs like this.
Hi Marcel- apologies for what I'm sure is an annoying question (and I know you guys are working hard), but can you please tell us when we might see another beta firmware release? I'd like to be on 365 (DD1, Porsche BME), but I backed out of it after seeing the (known issue of the telemetry LEDs getting stuck (ABS/TC) is fixed.
for you and anyone else having issues with the wheel disconnecting/freezing i believe the porce BME is freezing because one of the pins is losing connection for a split second when the wheel is under a lot of stress or high ffb. i tested this by being very gentle with the wheel and very low ffb it never froze. im on the latest 365 beta driver and latest beta fw on the BME.
so i fixed this issue by tightening the wheel quick disconnect as tight as i could with my hands but im pretty strong (no disrespect intended) some of you might benefit from a "strap wrench" usually used for oil filters
i also put some lithium grease between the big quick disconnect nut and the spacer that squeezes the rubber piece on the shaft. with out the grease there was too much friction so i couldnt get it as tight.
if you cant get tight enough try using that silver screw it came with to lock the quick disconnect 🤷♂️
i havent had the wheel disconnect since its been like 2 weeks. iv also ran it at 100% ffb and zero issues. hope this help you guys!
EDIT: After windows fresh installation it keeps crashing every time in some particular sitatuation where wheel emulates bumper imho like when i do Eau Rouge on F1 2019 or i hit curbs in ACC, tried every drivers/fw combination
EDIT2: Tried from v365 to v328, downgrading motor wheel and base fw everytime and rebooting, keeps doing weird ffb and get stuck in those situations, starting thinking i need a new base. i'm going to record and post video here
Been stable for some time. Glad that Thomas allowed for the FanaLab 1.24 release even though he was not happy with it. Also I am supposing that no more releases of FanaLab means the next one will be as Thomas wanted the first.
I am pleased to report that this combination along with the iRacing Options and Tuning settings shown in image form (showing the FanaLab interface can also be adjusted through the Fanatec Wheel Properties interface) gives a great response and intuitive feel while driving the Pro 2000.
Keep up the good work.
Maurice BöschenMember, CSL E RP1 PS4 beta tester, RMcL BT, CS SWFORM V2 Beta test, DD Beta Tester, PHub Beta Tester, P BME beta tester
Bill, you should definitely increase the Interpolation Filter. OFF is absolutely not good for the 60Hz FFB refresh rate of iRacing...
Marcel did not quoted you here, it was the quote above that one where he suggested to use Game Mode and that it's most likely only a visual lag and no input lag.
Removing the sleeved cable from PSU to Motherboard made the trick, probably my USB ports were badly powered, everything fine with v365 last FWs and Fanalab as well.
First of all sorry for my bad english
I have the Fanatec DD1 Ps4 wheelbase and driver 346
I played assetto corsa today and after a long time the wheelbase froze again
I have the bmw gt2 wheel on it
i could neither steer nor accelerate or anything else the steering wheel only turned completely to the left
only a restart helped
is there a solution to the problem now?
last I had the problem 1 month ago
Steering Wheel Model (product ID): CSL ELITE RACING WHEEL
Driver Version: ....365
Base FW Version: ....672
Wheel FW Version: ....22
FanaLab Version: ...none FanaLEDs
Hi, just upgraded from v328 to 365 and now no throttle rumble in my Clubsport Pedals V3 in game, in ACC, and both rumble tests for brake and throttle are not working now ?
Everything else works great and I do like the tuning menu included in there now.
Hello and Thank You to the Team and community providing info and Help.
I just want to add to the Universal Hub B, X button issue. ALL of the Functions of the top buttons are working , the funky switch and all paddles on the advanced paddle module. Its Only the external /Extension buttons.
Im sorry if im restating information , But all i saw was people restate the button not working and skipping what is.. I thought this might be helpful. Thankyou!
i have a problem with my elite csl bundle i updated to driver 365 but the steering was still connected to the base now, the pc does not read the base, how can i downgrade to the old firmware or how can i solve the problem. please help me
i have a problem with my elite csl bundle i updated to driver 365 but the steering was still connected to the base now, the pc does not read the base, how can i downgrade to the old firmware or how can i solve the problem. please help me ,I don't know how to do the downgrade procedure
Comments
Brand new CSL Elite + Formula V2 + CSL Pedals working fine till i updated to those drivers to try Fanalab.
Wheel was like driven by the devil, as i hit curbs it was going to break my desk and 4 tim drivers crashed and my wheel has been disconnected, now i rolled back to v334 downgrading everything except Formula FW and seems, SEEMS it works fine again, but i can't use Fanalabs like this.
I believe CSL can only use driver up to v347 so try that and see how it goes.
hard to tell, because when you update the firmware, you always have to run a new calibration of the shifter and something might have gone wrong there
Which platform?
Which game?
Which settings?
Fer Shifter simply has a design flaw, after isolating the board it works in 99% of the problem cases.
Hi Marcel- apologies for what I'm sure is an annoying question (and I know you guys are working hard), but can you please tell us when we might see another beta firmware release? I'd like to be on 365 (DD1, Porsche BME), but I backed out of it after seeing the (known issue of the telemetry LEDs getting stuck (ABS/TC) is fixed.
for you and anyone else having issues with the wheel disconnecting/freezing i believe the porce BME is freezing because one of the pins is losing connection for a split second when the wheel is under a lot of stress or high ffb. i tested this by being very gentle with the wheel and very low ffb it never froze. im on the latest 365 beta driver and latest beta fw on the BME.
so i fixed this issue by tightening the wheel quick disconnect as tight as i could with my hands but im pretty strong (no disrespect intended) some of you might benefit from a "strap wrench" usually used for oil filters
i also put some lithium grease between the big quick disconnect nut and the spacer that squeezes the rubber piece on the shaft. with out the grease there was too much friction so i couldnt get it as tight.
if you cant get tight enough try using that silver screw it came with to lock the quick disconnect 🤷♂️
i havent had the wheel disconnect since its been like 2 weeks. iv also ran it at 100% ffb and zero issues. hope this help you guys!
Win 10
F1 2019, ACC and AC
Fanatec recommended
Crash everytime with 365, sometimes with 334.
Fanalab Dynamic FFB seems to be the problem.
EDIT: After windows fresh installation it keeps crashing every time in some particular sitatuation where wheel emulates bumper imho like when i do Eau Rouge on F1 2019 or i hit curbs in ACC, tried every drivers/fw combination
EDIT2: Tried from v365 to v328, downgrading motor wheel and base fw everytime and rebooting, keeps doing weird ffb and get stuck in those situations, starting thinking i need a new base. i'm going to record and post video here
I think this should explain better my situation:
https://www.youtube.com/watch?v=GFyMhGmIlkQ&feature=youtu.be
Been stable for some time. Glad that Thomas allowed for the FanaLab 1.24 release even though he was not happy with it. Also I am supposing that no more releases of FanaLab means the next one will be as Thomas wanted the first.
I am pleased to report that this combination along with the iRacing Options and Tuning settings shown in image form (showing the FanaLab interface can also be adjusted through the Fanatec Wheel Properties interface) gives a great response and intuitive feel while driving the Pro 2000.
Keep up the good work.
Bill, you should definitely increase the Interpolation Filter. OFF is absolutely not good for the 60Hz FFB refresh rate of iRacing...
WheeLl: CSL ELITE PS4
Console: PS4
Driver: 356
Motor: 22 ( i think)
playing on a monitor
cant finde the right settings in the tuning menu, tried a few
What does dd mean?
Marcel did not quoted you here, it was the quote above that one where he suggested to use Game Mode and that it's most likely only a visual lag and no input lag.
DD = Direct Drive.
If i plug off my G933 headset seems it does not crash, maybe problem is usb related, still going mad to let this wheel work properly
Can you give me some detail about what exact crash you are talking about?
Removing the sleeved cable from PSU to Motherboard made the trick, probably my USB ports were badly powered, everything fine with v365 last FWs and Fanalab as well.
thanks
Hi, just upgraded from v328 to 365 and now no throttle rumble in my Clubsport Pedals V3 in game, in ACC, and both rumble tests for brake and throttle are not working now ?
Everything else works great and I do like the tuning menu included in there now.
Any help appreciated.
Thanks..
Hello Fanatec Team,
My setup:
In ACC, near the end of a 20 mn race, sudden loss of gear shifting on the V2.
I press ESC, reload my controller profile for the DD2 + V2, resume the race, the shifting is back but the force feedback is gone.
Drivers:
Repeated identical incidents yesterday and today.
Is my V2 defective ?
Please let me know what I can do to fix this, as it stands I cannot race.
Happy to contribute any log files if they exist to help you reproduce and fix this.
Thx.
Hello and Thank You to the Team and community providing info and Help.
I just want to add to the Universal Hub B, X button issue. ALL of the Functions of the top buttons are working , the funky switch and all paddles on the advanced paddle module. Its Only the external /Extension buttons.
Im sorry if im restating information , But all i saw was people restate the button not working and skipping what is.. I thought this might be helpful. Thankyou!
i have a problem with my elite csl bundle i updated to driver 365 but the steering was still connected to the base now, the pc does not read the base, how can i downgrade to the old firmware or how can i solve the problem. please help me
Tieni premuto il bottone di accensione per 8-9 secondi mentre sei collegato all usb del pc
ora cosa devo fare ?
É in modalita aggiornamento? Se si installi i drivers contenenti il fw che vuoi flashare
poi cosa faccio start firmwhare o restart wheel ? grazie per l'aiuto
Please stick to English language so everyone can understand what you are writing here..
i have a problem with my elite csl bundle i updated to driver 365 but the steering was still connected to the base now, the pc does not read the base, how can i downgrade to the old firmware or how can i solve the problem. please help me ,I don't know how to do the downgrade procedure
I’m sorry i just said him to push power button for 8-9 sec with usb plugged in
you need to flash the fw