never mind, I was able to reflash the BME again with the DeviceModuleBootLoader flasher.
But I'm wondering why flashing the wheel rims often gives me a headache as it happened quite some times already that the flashing process ends up with an error. Flashing the dd1 itself normaly works without a problem.
I have updated my CSW 2.5, Pedals V3and RIM Formula F1 2019 to the latest Drivers and Firmware to use Fanalab.
PC Driver: V365
Motor FW Wb 2.5: V22
Wb FW: V672
Wheel FW: V34
All seems to work fine with one exception. Rumble motors on the pedals don't work. Neither brake nor acceleration. They remain quite in Driver testmenu. Do I miss something?
Did you try to reset to default values in vibration tab in fanalabs? With me the rumble motors and lights were on all the time. Fixed when i reseted everything to default.
Who and where write this, that the New Beta does not Support csl basees? I install the new driver and update the firmware.So far no problem on project cars 2 on pc and gt sport on ps4. The only thing that scares me, on the new firmware the fan does not spinns after a few minutes of play like on the firmware that came with the 347 driver. I fear the motor could be damaged by overheating. Is this behavior normal and the temperature fancurve is rased, or is this a bug that can damage your wheelbase.(The fan will only spinn for some seconds when the base is Switching on.So that is no hardware failure.)
for what I understand this driver supports CSW or CSL bases but support for BME (button box endurance) on CSW or CSL bases is not ready yet (probably there is closed beta for BME on CSW )
Hi. So I have the DD1 version PS4 with its respective steering wheel, it is not necessary to upgrade to v365, right? There is no change in this model ... or I'm wrong. Thank you!
Thank you for the answer.No the plastic shell of the wheelbase is not so hot but it does not have direct contact whith the motor, so it is enought air as a Isolation ,and you can't juge if it is too hot.
For anyone wanting to get the buttons working again on their Universal Hub, I rolled back to driver 346, but it wasn't until I rolled back my wheel base (CSW 2.5) to the f/w that came with 346, did the buttons begin working again. I imagine that it's the same with 352. So remember to roll back your wheel base firmware as well.
I installed the 365 drivers.. now I can’t get into the fanatec control panel whatsoever.
to start with they showed up in the usb controllers. But they disappear when you try and load the control panel.
If i delete the 'usb input device' and scan for new devices it will be listed in the windows game controller panel again. when I load the properties it will come up with 'initializing device control panel...' only to disappear and then the devices removing themselves from the windows game controllers and the device manager having another 'USB input device' with an error - Error is: Windows cannot start this hardware device because its configuration information (in the registry) is incomplete or damaged. (Code 19)
Ive tried uninstalling and reinstalling drivers 336,346,356,365 - and I can flash the base firmware by using the force 8sec hold on the power button for each driver and it finishes correctly, but still no changes on being able to load the control panel.
so I’m completely stuck now.. tried every USB port I have, new cables, deleted all non used usb devices with usbview. Drivers just will not load in window 10.... any suggestions?
obviously a windows issue as podium base still works fine, when you delete the fanatec drivers completely and load the use controller properties the windows default controller window pops up immediately and all button presses etc. are registered.
I had the same issue last night when I went from 346 to 365 but I can't remember how I fixed it now, lol. It wasn't from changing USB ports. Ah, now I remember. You have to click on the download like you go to install it again but this time you click on repair and that should fix it.
Comments
How do I do that? 👇️
Update driver and FW separately to isolate an issue. Most likely it will be driver OR firmware.
Currently running:
New driver 365 & Fanalab 1.24
DD2 ID - S/N:KL25900737
DD2 - WB FW 672
WB MFW 38
UHX - R300 (PC) + APM
UHX ID - S/N:VX22900558
After updating the new driver (365) and wheel base firmware (672), some UHX buttons are not recognized. APM everything being recognized.
1st attempt : driver (356) and wheel base firmware (672), the problem still persists.
2st attempt: driver (365) and wheel base firmware (670), everything works perfectly.
Where do I find this? 👇️
- Motor DD2: PWBDD2_EBLDC_V38_rev448_app
-EBLC_V38_rev488_app???
After updating to 675 I was asked to update the BME.
The update finished with an error and now my BME is not recognized again.
Is there any way to start the updater for the BME again or is there any other way to bring it back to life again?
never mind, I was able to reflash the BME again with the DeviceModuleBootLoader flasher.
But I'm wondering why flashing the wheel rims often gives me a headache as it happened quite some times already that the flashing process ends up with an error. Flashing the dd1 itself normaly works without a problem.
It is included in the driver package. if you update the Motor FW it will load the Hex automatically.
Hello Team,
I have updated my CSW 2.5, Pedals V3and RIM Formula F1 2019 to the latest Drivers and Firmware to use Fanalab.
PC Driver: V365
Motor FW Wb 2.5: V22
Wb FW: V672
Wheel FW: V34
All seems to work fine with one exception. Rumble motors on the pedals don't work. Neither brake nor acceleration. They remain quite in Driver testmenu. Do I miss something?
Thanks.
Did you try to reset to default values in vibration tab in fanalabs? With me the rumble motors and lights were on all the time. Fixed when i reseted everything to default.
Hi, did it but no Change. Rumble motors don't work in PC Driver test menu.
So, is this the latest versions of all software?
Hey, I've just installed the new V365, along side the V672 and Fanalab 1.24 on my Podium F1 DD1. I've given it a short go. So far, no problem.
yes, that is what I got
Who and where write this, that the New Beta does not Support csl basees? I install the new driver and update the firmware.So far no problem on project cars 2 on pc and gt sport on ps4. The only thing that scares me, on the new firmware the fan does not spinns after a few minutes of play like on the firmware that came with the 347 driver. I fear the motor could be damaged by overheating. Is this behavior normal and the temperature fancurve is rased, or is this a bug that can damage your wheelbase.(The fan will only spinn for some seconds when the base is Switching on.So that is no hardware failure.)
for what I understand this driver supports CSW or CSL bases but support for BME (button box endurance) on CSW or CSL bases is not ready yet (probably there is closed beta for BME on CSW )
more info have https://forum.fanatec.com/profile/Marcel%20Pfister
is you base few minutes after switching on hot to a touch?
fun curve is probably intended, no need to blow air on cold metal
Hi. So I have the DD1 version PS4 with its respective steering wheel, it is not necessary to upgrade to v365, right? There is no change in this model ... or I'm wrong. Thank you!
Driver 356
Firmware 670
Where did you find Fanalab 1.24??
read the changelog of 361 and 365 and judge by yourself, there are tons of improvements for your wheel.
changes are in 2 posts
1 post https://forum.fanatec.com/discussion/1777/fanatec-beta-driver-v361-now-v365-for-csl-csw-and-podium-bases-all-wheels/p1
and https://forum.fanatec.com/discussion/comment/43056/#Comment_43056
fanalab 1.24 is in https://forum.fanatec.com/discussion/1438/podium-button-module-endurance-software-package-v1-2-incl-instructions-only-podium-dd/p1
I relay think it is time for community to write summary for all this arcane forum mess or even maintain github pages
for someone that is not every day on this forum that answer has very little actionable information
what should I do, list him all the 44 changes or what? :D
Its literally EVERYTHING in the very first post!
Thank you for the answer.No the plastic shell of the wheelbase is not so hot but it does not have direct contact whith the motor, so it is enought air as a Isolation ,and you can't juge if it is too hot.
links is all that is needed
Here: https://forum.fanatec.com/discussion/1438/podium-button-module-endurance-software-package-v1-2-incl-instructions-only-podium-dd#latest
Just download the podium package and you will find in the folder the 1.24 Fanalab version.
Installed successfully. Have driven many hours without any single issue. Really stable and good update:
CSW 2.5
BMW Rim
Thank you very much team,
BR
G
I just tested on my PS4 DD, works great so far. Left stick is not inverted, funky stick is not mapped to "X+PS", just the "X" button. So far, so good!
For anyone wanting to get the buttons working again on their Universal Hub, I rolled back to driver 346, but it wasn't until I rolled back my wheel base (CSW 2.5) to the f/w that came with 346, did the buttons begin working again. I imagine that it's the same with 352. So remember to roll back your wheel base firmware as well.
Podium f1:
I installed the 365 drivers.. now I can’t get into the fanatec control panel whatsoever.
to start with they showed up in the usb controllers. But they disappear when you try and load the control panel.
If i delete the 'usb input device' and scan for new devices it will be listed in the windows game controller panel again. when I load the properties it will come up with 'initializing device control panel...' only to disappear and then the devices removing themselves from the windows game controllers and the device manager having another 'USB input device' with an error - Error is: Windows cannot start this hardware device because its configuration information (in the registry) is incomplete or damaged. (Code 19)
Ive tried uninstalling and reinstalling drivers 336,346,356,365 - and I can flash the base firmware by using the force 8sec hold on the power button for each driver and it finishes correctly, but still no changes on being able to load the control panel.
so I’m completely stuck now.. tried every USB port I have, new cables, deleted all non used usb devices with usbview. Drivers just will not load in window 10.... any suggestions?
obviously a windows issue as podium base still works fine, when you delete the fanatec drivers completely and load the use controller properties the windows default controller window pops up immediately and all button presses etc. are registered.
I had the same issue last night when I went from 346 to 365 but I can't remember how I fixed it now, lol. It wasn't from changing USB ports. Ah, now I remember. You have to click on the download like you go to install it again but this time you click on repair and that should fix it.
Yea I’ve uninstalled, repaired and restarted pc with every combination of drivers and still nothing changed so far.
drastic measures had to be taken.
fresh windows install (even though it was already very clean and only a few months old)
installed 365 drivers straight away before anything else and low and behold it jumps straight into fanatec control panel with no errors whatsoever.
super annoying though as I’ve now got hours getting my windows and everything back installed how I want it.
I tried literally everything before a windows wipe nothing worked that I could find