No useless but in your case the LC brake has a higher resolution when connected via USB so I would stick with USB connection if you prefer a slightly higher resolution of the brake pedal.
I have the CSL elite 1.1v with the Nascar only podium wheel. I can't calibrate it with the normal software it says to download the Fanalab. When i do it doesn't say i have a wheel. Has this be resolved? I need help setting it up. It doesn't recognize my shifter or can't i change any force feedback strength.. Really could use some help on a new setup.
Maurice BöschenMember, CSL E RP1 PS4 beta tester, RMcL BT, CS SWFORM V2 Beta test, DD Beta Tester, PHub Beta Tester, P BME beta tester
Which driver do you have installed with which base firmware? For the Podium Hub you need at least driver 346, which also has the center calibration added to the driver menu on the settings Tab. No need for FanaLab as FanaLab can NOT calibrate the center at all, only the driver can.
Okay, new to this but i believe I have v336, only using the PC version so there is no buttons at all on my wheel. Can't get the shifter calibrated or center the wheel. Probably user error.
Maurice BöschenMember, CSL E RP1 PS4 beta tester, RMcL BT, CS SWFORM V2 Beta test, DD Beta Tester, PHub Beta Tester, P BME beta tester
Unfortunately with your wheel base you can not change any tuning menu settings without another Fanatec steering wheel. The Podium Hub doesn't have a display and no Dpad and your wheel base has limited electronics so the Tuning Menu is also not available in the driver or in FanaLab. What driver 346 gives you is the Podium Hub compatibility so the steering wheel is detected by the driver and the possibility to calibrate the center but you still won't be able to adjust any FFB settings of the Tuning Menu.
The Button Module Endurance is not yet compatible with the CSL Elite Wheel Base, that would be your only chance with the Podium Hub in the future. For now you need a different Fanatec Wheel with a Display and Dpad to adjust Tuning Menu settings as it's impossible otherwise at this moment.
Well... It's described in the compatibility part of the Podium Steering wheel Nascar that control of Tuning Menu is not possible without an additional button module which is not yet available...
Can someone confirm that the slider from the brake of the CSP v3 dont working at all? It doesnt have any effect on brakeforce when sliding up an down in this driver verson..
Hope you had a great weekend taking into account the worldwide circumstances.
I have been using v365 for about a week and it's working good with my Formula Black wheel and V2.5 base. The only problem I'm having is with my v3 inverts, I had to switch from manual calibration to auto, because brake pedal (w/pref kit) became on predictable. Thank you Maurice
Did you mean v356 or did you get your hands on a special version? Which base did you firmware upgrade? Did you do the upgrade without the wheel attached? Did you use the long and updated guide that Fanatec recently made? Please share your experience as I am very eager but also afraid to upgrade my DD1 PS4 base and motor.
I have been having this issue for a while, it just started after i updated to v356 afterwards i have been running everything from 346 to all beta drivers and keep getting the same issue. The rim just freezes on the same spots on the track on random times, FFB keeps working, but the rim gets frozen and no buttons can be used. I'm curious, am i the only one with the issue or there are other people ?
I'm was having the same issues to, but just curious are you using the formula v2 wheel? I actually just rolled back driver and firmware today! I am now running,
PC Driver 347
WB FW 656
SW FW 28
Motor FW 22
I have been using this combination pretty much all day yesterday and no stoppages so far and this is the longest I have gone without the wheel freezing since I started having issues!
Anyway hope that helps
By the way you can get fw from driver 336, or at least that is where i got them which you can get from downloads on formula v2 web page.
Comments
Yes when you have CSP v3
I have a CSL Elite LC.
So it is useless I guess...
No useless but in your case the LC brake has a higher resolution when connected via USB so I would stick with USB connection if you prefer a slightly higher resolution of the brake pedal.
Ok, thank you Maurice.
when are they fixing this?, been weeks now
It would be nice with an update, at least to know if they are still healthy and working in the crazy human-malware times.
I have the CSL elite 1.1v with the Nascar only podium wheel. I can't calibrate it with the normal software it says to download the Fanalab. When i do it doesn't say i have a wheel. Has this be resolved? I need help setting it up. It doesn't recognize my shifter or can't i change any force feedback strength.. Really could use some help on a new setup.
Which driver do you have installed with which base firmware? For the Podium Hub you need at least driver 346, which also has the center calibration added to the driver menu on the settings Tab. No need for FanaLab as FanaLab can NOT calibrate the center at all, only the driver can.
Okay, new to this but i believe I have v336, only using the PC version so there is no buttons at all on my wheel. Can't get the shifter calibrated or center the wheel. Probably user error.
As said you need at least driver 346. Your driver 336 simply does not know a product called Podium Hub :D
With driver 346 you can calibrate the center in the driver without the need of any buttons.
Will Fanalab help me with force feed back settings? I thought you could set the forces higher with the software instead of using the iracing sets.
No, your wheel base is not properly supported by FanaLab
ok
Funny it says to use that to change settings on the Fanatec website. Oh well I'll try the V346
Thanks
Unfortunately with your wheel base you can not change any tuning menu settings without another Fanatec steering wheel. The Podium Hub doesn't have a display and no Dpad and your wheel base has limited electronics so the Tuning Menu is also not available in the driver or in FanaLab. What driver 346 gives you is the Podium Hub compatibility so the steering wheel is detected by the driver and the possibility to calibrate the center but you still won't be able to adjust any FFB settings of the Tuning Menu.
Will I be able to do that if a had a button set or do I need something else, its crazy there is no FFB settings within the base.
Thanks for the info..coming from a G27 LOL
The Button Module Endurance is not yet compatible with the CSL Elite Wheel Base, that would be your only chance with the Podium Hub in the future. For now you need a different Fanatec Wheel with a Display and Dpad to adjust Tuning Menu settings as it's impossible otherwise at this moment.
ok thanks.. wish I had known that before I dropped $400
Well... It's described in the compatibility part of the Podium Steering wheel Nascar that control of Tuning Menu is not possible without an additional button module which is not yet available...
Hi everyone!
Hope you had a great weekend taking into account the worldwide circumstances.
Shall we expect the firmware any time soon to be released?
Best,
Miguel/Nikos
Hello Fanatec mates,
Can someone confirm that the slider from the brake of the CSP v3 dont working at all? It doesnt have any effect on brakeforce when sliding up an down in this driver verson..
Hope you had a great weekend taking into account the worldwide circumstances.
I second that question, it would be really nice to have some information about the progress and what we can expect.
3 weeks later and no updated release?
nothing new yet, no.
Thanks!
I have been using v365 for about a week and it's working good with my Formula Black wheel and V2.5 base. The only problem I'm having is with my v3 inverts, I had to switch from manual calibration to auto, because brake pedal (w/pref kit) became on predictable. Thank you Maurice
Did you mean v356 or did you get your hands on a special version? Which base did you firmware upgrade? Did you do the upgrade without the wheel attached? Did you use the long and updated guide that Fanatec recently made? Please share your experience as I am very eager but also afraid to upgrade my DD1 PS4 base and motor.
I've been using v346 on my DD1 for PC for about 3-4 months now. No issues so far.
I have been having this issue for a while, it just started after i updated to v356 afterwards i have been running everything from 346 to all beta drivers and keep getting the same issue. The rim just freezes on the same spots on the track on random times, FFB keeps working, but the rim gets frozen and no buttons can be used. I'm curious, am i the only one with the issue or there are other people ?
I'm was having the same issues to, but just curious are you using the formula v2 wheel? I actually just rolled back driver and firmware today! I am now running,
PC Driver 347
WB FW 656
SW FW 28
Motor FW 22
I have been using this combination pretty much all day yesterday and no stoppages so far and this is the longest I have gone without the wheel freezing since I started having issues!
Anyway hope that helps
By the way you can get fw from driver 336, or at least that is where i got them which you can get from downloads on formula v2 web page.